|
Publications:
Journal
Papers:
ZHANG, L. C. and MAHDI. M., (1995a),
Applied Mechanics in Grinding,
Part IV: Grinding Induced Phase Transformation.
Int. J. Mach. Tools Manuf.,
35/10, (1995) 1397‑1409.
MAHDI, M. and ZHANG, L. C., (1995b),
The Finite Element Thermal
Analysis of Grinding Processes by ADINA,
Computer & Structure,
56, (2/3) (1995) 313-320.
ZHANG L. C and MAHDI, M, (1996a),
Plastic Behaviour of Silicon
Subjected to Micro-Indentation,
Journal of Materials Science, 31/21 (1996)
5671-5676.
MAHDI, M. and ZHANG, L., (1997a),
Applied Mechanics in Grinding-V:
Thermal Residual Stresses,
Int. J. Mach. Tools Manufact.,
37/5 (1997) 619-633.
MAHDI, M. and ZHANG, L., (1997b),
Applied Mechanics in Grinding ,
Part VI: Residual Stresses and Surface Hardening by
Coupled Thermo-Plasticity and Phase Transformation,
Int. J. Mach. Tools
Manufact,
38/10-11 (1998) 1289-1304.
MAHDI, M. and ZHANG, L., (1999a),
Residual Stresses in Ground
Components Caused by Coupled Thermal and Mechanical
Plastic Deformation, Submitted in May 1998 to
Journal of Materials
processing Technology
Volume 95, Issues 1–3, 15
October 1999, Pages 238-245.
MAHDI M. and ZHANG L.,
(1999b) Applied Mechanics in
Grinding, Part 7: Residual stresses induced by the full
coupling of mechanical deformation, thermal deformation
and phase transformation, International Journal of
Machine Tools and Manufacture,
1999, 39: 1285-1298.
MAHDI, M. and ZHANG, L.,A
Numerical Algorithm for the Full Coupling of Mechanical
Deformation, Thermal Deformation and Phase
Transformation in Surface Grinding,
Computational Mechanics,
2000, 26/2 148-156.
MAHDI, M. and ZHANG, L.,
An
adaptive three-dimensional finite element algorithm for
the orthogonal cutting of composite materials,
Journal of Materials Processing
Technology,
2001, 113/1, 368-372.
MAHDI, M. and ZHANG, L.,
A
finite element model for the orthogonal cutting of
fiber-reinforced composite materials, Journal of
Materials Processing Technology,
2001, 113/ 1, 373-377.
Mofid Mahdi,
An Optimal Two-Dimensional
Geometry of Flywheel for Kinetic Energy Storage, Int. J.
of Thermal & Environmental Engineering, Volume 3, No. 2
(2011), 67-72 .
Mofid Mahdi, A Thermal
Analysis of An Improved Rankine Steam Power Cycle ,
International Journal of Mechanical Engineering ( IJME
), Vol.1, Issue 2 Nov 2012 25-36.
Mofid Mahdi, Iqbal
Marie, Numerical Simulation of
Concrete Mix Structure and Detection of its Elastic
Stiffness, Journal of Computational Engineering and
Physical Modeling. Article 2, Volume 1, Issue 1, Winter
2018, Page 12-22
Mofid Mahdi, Iqbal Marie,
Three-Dimensional Modelling of
Concrete Mix Structure for Numerical Stiffness
Determination, Journal of Computational Engineering and
Physical Modeling. Volume 1, Issue 3, summer 2018, Page
15-27.
Abdul Kareem Abdul Jawwada, Mofid Mahdi and Nabeel
Alshabatat, The role of
service-induced residual stresses in initiating and
propagatingstress corrosion cracking (SCC) in a 316
stainless steel pressure-relief-valvenozzle set,
Engineering Failure Analysis 105 (2019) pp 1229–1251.
Conference
Papers:
ZHANG L. and MAHDI M. (1994), A Numerical
Investigation into The Micro-Indentation of Silicon,
International Ceramic Monographs, International
Conference, Sydney, Australasian Ceramic Society,
2, (1994) 644-650.
MAHDI. M. and ZHANG. L., (1994),
Correlation Between Grinding
Conditions and Phase Transformation of An Alloy
Steel,
Proceedings of advanced computational methods in heat
transfer III, , August, (1994) 193-200.
MAHDI, M., and ZHANG, L., (1996b), A Theoretical
Investigation on The Mechanically Induced Residual
Stresses Due to Surface Grinding, Progress of
Cutting And Grinding, JSPE, , III,
International Conference on Progress of Cutting and
Grinding (1996) 484-487.
MAHDI, M. and ZHANG,
L., (1997c), An Adaptive Method for Predicting
Residual Stresses Associated With Grinding Induced Phase
Transformation, The 12th annual meeting of ASPE,
October 5-10, (1997) 303-306.
MAHDI M and ZHANG L., (1998c), Residual Stresses in
Ground Components: Fully Coupled Thermo-Mechanical
Deformation and Phase Transformation, Proceedings
of International Conference on Progress of Cutting and
Grinding, Urumqi and Turpan, China, 5-9 October
(1998) 453-458.
MAHDI M and ZHANG L., (1998d), Residual Stresses in
Ground Components: Effect of thermo-mechanical
deformation, Proceedings of International
Conference on Progress of Cutting and Grinding,
Urumqi and Turpan, China, 5-9 October(1998) 447-452.
MAHDI, M. and ZHANG, L.,
(1999a), Residual Stresses in Ground Components:
Distribution Effect of Surface Traction, The
Second Australasian Congress on Applied Mechanics,
Canberra, Australia, 10-12 February (1999).
MAHDI, M. and ZHANG, L.,
(1999b), A Numerical Treatment for the Coupling of
Mechanical Deformation, Thermal Deformation and Phase
Transformation in Surface Grinding, ABTEC’99
International Conference on Abrasive Technology,
November 21-23,1999 Brisbane, Australia.
MAHDI, M. and ZHANG, L.,
(1999c), Simulation of Orthogonal Cutting: The Effect
of Separation Criteria and Cutting Tool Geometry,
ABTEC’99 International Conference on Abrasive
Technology, November 21-23,1999 Brisbane, Australia.
Mahdi, M, On the
Modelling of the Material Processing by the Finite
Element Method: Applications in Grinding and Cutting
Processes, Proceedings of the 4th
Jordanian International Mechanical Engineering
Conference, JIMEC 2001, Amman, Jordan.
M. Abdel-Jaber, S.
Al-Sadder, A. Shatnawi, M. Mahdi, "Equilibrium
Configurations of Heavy Elastica Beams Under Unilateral
Contact Constraints", in B.H.V. Topping, M.
Papadrakakis, (Editors), "Proceedings of the
Ninth International Conference on Computational
Structures Technology", Civil-Comp Press, Stirlingshire,
UK, Paper 210, 2008. doi:10.4203/ccp.88.210 |
